Let’s discuss some nuances of building of garage.

Beams for building produce usually from pine, larch or fur-tree. The wood used for manufacturing of beams, necessarily should be dry, because the drier beam, it is stronger and the caves in under loading less.

Beams of garret overlapping lean against walls only with the ends, and that they didn’t cave in, it is necessary to calculate and stack correctly them on distance no more than 1 m from each other.

The beam representing bar, it is possible to replace with two boards, the general section equal to bar. These boards connect by means of nails, having them in chessboard order. It is possible to use also the ordinary thick boards put on edge. In walls the ends of beams close up as follows. Beams put on walls or insert into nests specially left for them.

For prevention of rotting of beams between walls and the ends of beams it is necessary to leave space. With that end in view the nests left in brick walls for packing of beams, it is necessary to make more volume, than the ends of beams. The bottom part of nest, which should be equal, it is possible to level by means of concrete. On concrete put two-three layers of roofing felt or roofing material. In brick buildings depth of nests usually makes 25 cm, and the ends of beams put on length not less than 15 cm.

Before packing the ends of beams prepare and wrap up two layers of roofing felt. End faces of beams don’t pitch and don’t close roofing felt. Lateral and top the parties of beam after packing close up with solution. Between extreme beams and wall there should be backlash not less than 50 mm, which close up by sticks. Between sticks and beam it is desirable to lay roofing felt or roofing material strip.

Also during building you could beat so-called cranial sticks section 4×4 cm. Plates should adjoin densely to each other and be flush with the bottom party of beam. If the ceiling isn’t planned to plaster, plates plane.

Slope of the roof you should grease with the greasing consisting of clay and sand, or cover with roofing felt. After greasing drying fall asleep shaving, sawdust, wood sheet. With a view of fire-prevention safety sawdust or shaving from above fall asleep the dry earth or small slag on height 5 cm. On top of beams it is desirable to nail up the cut board flooring. It will prevent displacement. Garret overlapping is better to warm fire-resistant not decaying plates.

And let me say some words about adaptations for safe entrance to garage. Absolutely not bad, even for skilled drivers to have in garage the device, not allowing driving further, than it is necessary. Such adaptations exists much. We will consider some of them.

Hang up on distance 20…30 cm from back wall of garage old tyre cover at bumper level. As soon as the car will concern it, press brake. Suspend to ceiling on thin cord small soft subject like tennis ball or, we will tell children’s toy. Suspension bracket place choose so that at correct statement of the car the subject slightly concerned windshield. Now drive to garage, as signal of feet will serve the subject touch to glass.

If you need help with finding best portable garage – this site will help. Lots of samples of car garage products and direct access to the car garage sellers. All contact info on the site.

P.S. And don’t let laziness to stop you from finding the best deal about car garages. Don’t forget that we are living in the world where info makes life easier.

Due to this if you are properly armed with the info in your sphere of interest you can be sure that you will always find the way out from any bad situation. So, please make sure to track this blog on a regular basis or – best of all – sign up to its RSS. In such an easy way you will have your hand on the pulse of the latest informational updates here. Blogs can be helpful, you just need to know how to use them.

If garage building — your first experience in building business and you haven’t learnt to do laying correctly yet we advise to you to arrive as follows: lay bricks along the future wall of garage without solution and so that between them there was backlash in the size equal to thickness of seam, that is 12 mm. After that, pull cord so that it is receded from wall edge on 1-2 mm. In this case the cord doesn’t move during laying of bricks on solution and allows maintaining straightforwardness of laying.

Further conduct job as follows: the right hand with the help of device scoop portion of solution, the left hand take the brick laid earlier without solution, put on its place solution. After solution alignment return brick into place and, slightly having knocked on it with the handle of your device for building, press it into solution so that the seam was the necessary thickness, and the brick top was on one line with cord.

After that the left hand take the second brick, on its place also put solution, level, with the help of device pull a few solution over edge of the first brick and will put the second brick back, also pressing it into solution that it upwards was on one line with cord.

Following bricks stack as, as required lifting cord. If the solution part, into which the brick is pressed, supports wall plane, at once remove it, put back in bucket and mix with solution being there.

To put up walls it is possible and without the help of cord. In this case on under construction wall lay piles of bricks through each 1-1,5 m. Then take portion of solution on 3-5 bricks and spread out it to wall parts. On solution lay bricks one after another, slightly tapping on them with the handle of your device for building. During laying don’t forget to pull with the device small part of solution over edge before the laid brick.

After base pouring do garage floor. It can be cement or concrete.

For the device of concrete floor over platform throw sand layer of 10 cm and stamp it well. On sand it is necessary to lay layer of roofing felt, and it is possible to fill in bitumen mastic. Then you should put above layer of 10 cm pour concrete and stamp. The floor surface should be rough.

Cement floor do so: ground mix with rubble or gravel, level and condense. After that prepare dense cement mortal (on one part of cement of 5-6 parts of sand) and stack its layer 3—4 cm. After a while (3-4 days) cover floor with the second layer of cement mortal. But this time solution do by more liquid, mixing one part of cement with 2-3 parts of sand, and stack its more thin layer (1-2 cm). The cement floor during the following of 3-4 days is recommended to water 2-3 times a day. Such procedure will raise its durability.

If you need car garage – this site will help. Lots of samples of car garage products and direct access to the car garage sellers. All contact info on the site.

P.S. And don’t let laziness to stop you from finding the best deal about car garages. Don’t forget that we are living in the world where information quickly enhances the quality of our life.

Due to this if you are properly armed with the information in your topic you can rest assured that you will in any case find the way out from any bad situation. So, please make sure to get back to this site on a regular basis or – the least time consuming way of doing it – sign up to its RSS feed. In such an easy way you will have your hand on the pulse of the latest info updates here. Blogs can be helpful, you just need to know how to use them.